FA-TCJ10L85-03D, SFP+-SR 10Gbps LC Fiber Optical Transceiver MM 850nm Short Range 300M With DDM
With the intelligent fiber optic transceiver, the network management unit can monitor temperature, supply voltage, the laser bias current and the transmitting and receiving optical power in real time. The measurement of these parameters can help the management unit find out the fault position in the optical fiber link, simplify the maintenance work and improve the reliability of the system.
The Digital Diagnostics Monitoring (DDM, fault diagnosis function) of optical transceiver provides a means for monitoring the performance of the system, can help the system management predict use life of the fiber optic transceiver, isolate system fault and verify compatibility during installation.
1, Digital potentiometer (or ADC) instead of traditional adjustment resistor, access and read and write through serial data bus I2C ;
2, EEPROM (electrically erasable programmable read only memory) space composed of two space A0h and A2h: A0h is used to hold the fixed information; and A2h is mainly used to store the information related to the DDM monitoring function.
3, The module has monitoring function. Can report the real-time monitoring of temperature, power supply voltage, bias current, transmit power and receive power;
4, The fiber optic transceiver is with diagnostic function. The module monitors 5 reporting parameters of the module by appropriate excuse and judge if it is within the normal range . As specified in SFF-8472, each parameter has two levels of alarm, called Alarm and Warning alarms respectively, and each stage is divided into two alarms High and Low.
Main Characteristics Of FA-TCJ10L85-03D
SFP+ encapsulation with LC connector
With 850nm VCSEL Laser and PIN photo detector
LVPECL compatible data input/output interface
Up to 300m transmission on 2000MHz-km MMF
Power dissipation < 1W
Low EMI and excellent ESD protection
Laser safety meet standard IEC-60825 requirement
Compatible with RoHS
Compatible with SFF8472
Optical Performance
(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)
| Parameter | Symbol | Min. | Typ. | Max. | Units |
| Transmitter Section |
| Center Wavelength | lo | 840 | 850 | 860 | nm |
| RMS Spectral Width | Dl | - | - | 0.45 | dB |
| Average Output Power | Po | -5 | - | -1 | dBm |
| Extinction Ratio | Er | 3.0 | - | - | dB |
| Dispersion Penalty | | | | 3.9 | dB |
| Relative Intensity Noise | RIN12OMA | | | -128 | dB/Hz |
| Total jitter | Tj | IEEE 802.3ae | |
| Receiver Section |
| Center Wavelength | lo | | 850 | | nm |
| Receiver Sensitivity | Rsen | | | -11.5 | dBm |
| Stressed Sensitivity | Rsen | | | -10.5 | dBm |
| Receiver Overload | Rov | 0 | | | dBm |
| Return Loss | | 12 | | | dB |
| LOS Assert | LOSA | -17 | | | dBm |
| LOS Dessert | LOSD | | | -15 | dBm |
| LOS Hysteresis | | 0.5 | | 4 | |
Electrical Performance
(Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V)
| Parameter | Symbol | Min. | Typ. | Max. | unit |
| Transmitter Section |
| Input Differential Impendence | Zin | 90 | 100 | 110 | Ohm |
| Data Input Swing Differential | Vin | 180 | | 700 | mV |
| TX Disable | Disable | | 2.0 | | Vcc | V |
| Enable | | 0 | | 0.8 | V |
| TX Fault | Assert | | 2.0 | | Vcc | V |
| Deassert | | 0 | | 0.8 | V |
| Receiver Section |
| Output differential impendence | Zout | | 100 | | Ohm |
| Data output Swing Differential | Vout | 300 | | 800 | mV |
| Rx_LOS | Assert | | 2.0 | | Vcc | V |
| Deassert | | 0 | | 0.8 | V |
Maximum Transmitting Distance
| Parameter | Symbol | Min. | Typ. | Max. | Unit |
| Fiber Type | 850nm OFL Bandwidth | | | | | |
| 62.5 um | 160MHz-km | | | | 26 | m |
| 200MHz-km | | | | 33 | m |
| 50 um | 400MHz-km | | | | 66 | m |
| 500MHz-km | | | | 82 | m |
| 2000MHz-km | | | | 300 | m |
Product Tags:
|
|
Durable SFP 10G Optical Transceiver , MM SFP LC Transceiver Short Range 300M Images
|
